ecto-1

Hasbro's Latest Crowd-Funded HasLab Revealed: A 6" Scale Ecto-1!

At New York Comic-Con this morning, Hasbro revealed their latest crowd-funding project for the Plasma Series: an Ectomobile Anniversary edition.

Pre-order sales for the crowd funded project are up now. 12,000 total orders will be needed by December 2, 2024 for the project to go into production. You can get your order in here. More from Hasbro in their official press release below!

Ghostbusters Plasma Series Ectomobile (Anniversary Edition) [Base Model] 

(HASBRO | Retail Price: $324.99) 

 

Celebrate 40 frightfully funny years of Ghostbusters with the Ectomobile—one of the most iconic movie cars of all time! If the overall campaign is successfully backed, the base model offering will include: 

 

Ghostbusters Plasma Series 6-Inch-Scale Ecto-1 with Lights & Sounds (x1) 

1984 Ecto-1 Hubcaps (x4) 

Ghostbusters 1984 Ecto-1 Decal Sheet (x1) 

Removable, Rolling Gurney (x1) 

Ghostbusters Plasma Series Library Ghost Action Figure (x1) with Stand (x1), Library Book Stack Accessory (x1), and Library Book accessory (x1) 

Ghostbusters Plasma Series Slimer Action Figure (x1) with Stand (x1) 

 

This crowdfunded project, which includes both the base and deluxe models, will run from October 18, 2024, to 11:59pm ET on December 2, 2024, and requires 12,000 combined total (across Basic and Deluxe Models) backer orders to begin production. If successful, the project is estimated to ship around Fall 2025.  

 

Don’t let this Anniversary Ectomobile drive off and leave you behind—fund this project today and park the only 6-inch-scale Ecto-1 ever made, in your Ghostbusters collection!  

 

Ghostbusters Plasma Series Ectomobile (Anniversary Edition) [Deluxe Model] 

(HASBRO | Retail Price: $399.99) 

 

Celebrate 40 frightfully funny years of Ghostbusters, as well as 35 hilariously haunted years of Ghostbusters II, with the Ectomobile—one of the most iconic movie cars of all time! If the overall campaign is successfully backed, the deluxe model offering will include: 

 

Deluxe Model: 

Includes Base Model: 

o Ghostbusters Plasma Series 6-Inch-Scale Ecto-1 with Lights & Sounds (x1) 

o 1984 Ecto-1 Hubcaps (x4) 

o Removable Rolling Gurney (x1) 

o 1984 Ghostbusters Ecto-1 Decal Sheet (x1) 

o Ghostbusters Plasma Series Library Ghost Action Figure (x1) with Stand (x1), Library Book Stack Accessory (x1), and Library Book accessory (x1) 

o Ghostbusters Plasma Series Slimer Action Figure (x1) with Stand (x1) 

Plus: 

o Ghostbusters II Conversion Kit Ecto-1A Roof with Functioning Lights (x1) 

o Ecto-1A Red Rear Bumper with Ecto-1A License Plate (x1) 

o 1989 Ghostbusters II Ecto-1A Decal Sheet (x1) 

o Ghostbusters Plasma Series Ecto-Charger Pack Accessories (x2) 

o Ghostbusters Plasma Series Ecto-plasm Streams (x2) 

o 1989 Ecto-1A Hubcaps (x4) 

o Ghostbusters II Toaster Accessory (x1) 

o Ghostbusters II Hot Beverage Thermal Mug Accessory (x1) 

o Ghostbusters II Free-Balloon-for-the-Kids Accessory (x1) 

o Ghostbusters Plasma Series Proton Pack Accessories (x4) 

o Ghostbusters Plasma Series Proton Streams (x4) 

o Ghostbusters Plasma Series Ray Stantz (Ghostbusters II) Action Figure (x1) 

o Ghostbusters Plasma Series Winston Zeddemore (Ghostbusters II) Action Figure (x1) 

o Ghostbusters Plasma Series Egon Spengler (Ghostbusters II) Action Figure (x1) 

o Ghostbusters Plasma Series Peter Venkman (Ghostbusters II) Action Figure (x1) 

 

This crowdfunded project, which includes both the base and deluxe models, will run from October 18, 2024, to 11:59pm ET on December 2, 2024, and requires 12,000 combined total (across Basic and Deluxe Models) backer orders to begin production. If successful, the project is estimated to ship around Fall 2025.   

 

Don’t let this Anniversary Ectomobile drive off and leave you behind—fund this project today and park the only 6-inch-scale Ecto-1/Ecto-1A ever made, in your Ghostbusters collection!  

 

Two Iconic Movies, Two Anniversary Events, Two Ways to Commemorate 

 

2024 is an important year for the Ghostbusters franchise, seeing the release of Ghostbusters: Frozen Empire and celebrating not one but two milestone anniversaries: the 40th Anniversary of Ghostbusters and the 35th Anniversary of Ghostbusters II! We’d already saved the collecting world with the first-ever Ghostbusters HasLab, the Plasma Series Spengler’s Proton Pack (no longer available), and came back strong with an ambitious sequel known as the second-ever Ghostbusters HasLab, the Two in the Box Ghost Trap & P.K.E. Meter (no longer available).   

 

But we were at a cross-rip—er, a crossroads—regarding the third-ever Ghostbusters HasLab. How would we trap the perfect paranormal follow-up? Unfortunately, nobody could agree on any one idea. There was a lot of bickering, even more name calling, and believe it or not, no less than three atomic-weight-of-cobalt wedgies. At the end of the day, we just couldn’t believe that things had gotten so bad in the HasLab Lab that there was no way back. Because there were a few sparks of sweet humanity left in that burned-out workshop. We just had to figure out a way to mobilize it! 

 

We needed something no one had ever done before, something that would blow the doors off the competition, and something that would really get the fandom’s collective engine revving. We’re beyond proud to announce the first-ever 6-inch-scale Ectomobile ever. EVER! And with both a base and deluxe model available, you get to choose your ride! 

 

Everybody Can Relax… 

  

That’s right, we found the car, and boy is she a beaut! The Ectomobile is so much more than just an automobile—it’s an icon; ridiculously designed, ridiculously cool, and instantly recognizable. The Ecto not only drove onto the silver screen, but she also drove straight into our hearts. We only hope our Plasma Series Ectomobile will do the same! Measuring in at 22.5 inches long, the Ghostbusters Plasma Series Ectomobile (Anniversary Edition) is just shy of 2 feet long and comes with all the movie-accurate bells, whistles, and gadgets, die-hard fans expect.  

 

The HasLab Lab worked directly with our partners at GHOST CORPS to create the most authentic and movie-accurate 6-inch-scale Ectomobile possible. Our design team was even able to visit and photograph an actual Ecto, and boy howdy, did they get all up in that car’s business, as indicated by the eerily insane amount of detail included in this 6-inch-scale replica.  

 

VEHICLE DESIGN DETAILS: 

*Included In Deluxe Model Only  

 

Plasma Series 6-Inch-Scale Action Figure Compatibility 

Functioning Lights 

o Headlights (x4) 

o Front Bumper Strobe Lights (x2) 

o Parking Lights (x4) 

o Unity S6 Spotlight (x1) 

o Interior Dome Lights (x3) 

o Dashboard Light (x1) 

o Taillights (x4) 

o Reverse Lights (x2) 

o Removable Ecto-1A Amber Front Bumper Strobe Light* (x1) 

Removable Ecto-1 Roof Rack with Functioning Lights (x1) 

o Seek Light (x1) 

o Strobe Light (x1) 

o Force 3 XL Light Bar (x2) 

o Front Lights (x2) 

o Rear Lights (x2) 

Removable Ecto-1A Roof Rack with Functioning Lights* (x1) 

o Red Beacon Light (x1) 

o Strobe Light (x1) 

o Whelen Edge Light Bar (x1) 

o Force 4 XL Light Bar (x1) 

o Front Lights (x2) 

o Force 3 XL Light Bar (x1) 

o Rear Tank Lights (x2) 

Removable Dot-Matrix Display Decals* 

o GHOSTBUSTERS (x1) 

o WE’RE BACK (x2) 

Functioning Doors (x4) 

Functioning, Reversible Wheels (x4) 

Functioning Hood  

Highly Detailed Engine Sculpt 

Highly Detailed Undercarriage 

Highly Detailed Interior (Designed for Movie Accuracy) 

o Front 

§ 360-Degree Functioning Steering Wheel 

§ Dash-Mounted Speaker 

§ Dash-Mounted Scanner 

§ Illuminating Radio Face 

§ Heater 

§ Glove Box 

§ Ceiling-Mounted CB Radio with Handheld Microphone 

o Rear 

§ Jump Seat  

§ Fold-Down Jump Seat 

§ Phone with Handheld Receiver 

o Cargo 

§ Removable Oscilloscope/Guidance System Unit  

§ Removable Distribution Units  

§ Removable Processors  

· Powered by 4 AA Batteries (Not Included) 

· USBC Port for “Always On” Display Option 

 

FIRST-EVER PLASMA SERIES GHOST: THE LIBRARY GHOST 

The Library Ghost (aka the Gray Lady, Librarian Ghost, and Eleanor Twitty) 

Class IV. Anchored to the New York Public Library. 

 

The Library Ghost is the first-ever spirit the Ghostbusters encounter, and now she’s immortalized in 6-inch scale as one of the first-ever Plasma Series ghost action figures! Featuring 7 points of articulation and ethereal, movie-inspired deco and design, the librarian is ready to haunt your shelves! Includes library book accessory, stack of library books accessory, and stand. 

 

How did we not do this sooner? 

 

SECOND-EVER PLASMA SERIES GHOST: THE GREEN GHOST 

The Green Ghost (aka Slimer) 

Class V. Full Roaming Vapor. Formerly anchored to the Sedgewick Hotel. 

 

The Green Ghost—or Slimer, as he’s more commonly known—is arguably the most famous ghost in the Ghostbusters universe, and the first successfully busted specter! From pigging out on leftover room service to charging and sliming Venkman, this ugly little spud was an immediate fan favorite. Now, he’s finally making his gluttonous debut in the Plasma Series, featuring 4 points of articulation and classic Ghostbusters design and detail. Includes stand.  

 

THE GHOSTBUSTERS ARE BACK (IN THE PLASMA SERIES)! 

 

Yes, that’s right, Ghostbusters! They’re back with twice the know-how and twice the particle power to deal with all your supernatural elimination needs. So come, celebrate the grand re-opening with 4 Ghostbusters Plasma Series Ghostbusters II action figures (Deluxe Model only)! 

 

Back the Ectomobile (Deluxe Model) and you’ll receive all 4 Ghostbusters, featuring all-new head sculpts and wearing the highly sought-after charcoal jumpsuits! You’ll also receive 4 Proton Pack accessories and 4 Plasma Stream accessories, as well as 2 Ecto-Charger Pack accessories and 2 Ecto-plasm Stream accessories, so you can re-create favorite moments from Ghostbusters II. 

 

Additional Deluxe Model accessories include a toaster, Ghostbusters hot beverage thermal mug, and Ghostbusters balloon. 

 

“TWO WEEKS TO TULLY” EARLY BIRD SPECIAL 

  

We couldn’t celebrate the hilarious follow-up to Ghostbusters, the aptly titled Ghostbusters II, without including the unofficial fifth Ghostbuster! As a special bonus, if the Ghostbusters Plasma Series Ectomobile (Anniversary Edition) traps the minimum backer amount within the first 14 days of the campaign, all backers will receive a 6-inch Louis Tully (Ghostbuster) action figure! Yes, that means if the early bird special is unlocked in the first 2 weeks, EVERYONE that backs the project throughout the duration of the campaign will receive this awesome Ghostbusters action figure! That’s scary awesome. Includes Proton Pack (x1), Plasma Stream (x1), Ghost Trap (x1) and P.K.E. Meter (x1) accessories. 

 

A SUPERNATURAL CELEBRATION 

 

We here in the Ghostbusters HasLab Lab love this franchise just as much as you do. We’re not just labbies, after all, we’re fans. We grew up with these characters, we wanted to join the team, and their stories are irrevocably woven into the very fabric of our existence. And 40 and 35 years later, both Ghostbusters and Ghostbusters II remain very much woven into the fabric of pop culture. To say we’re honored to be a part of the amazing and inclusive legacy of Ghostbusters… well, that would be putting it mildly.  

 

Here's to 40 years of frights, delights, and saving the world, as well as 35 years of psychomagnotheric ecto-plasm, haunted paintings, and… well, saving the world! Back this project today and race to the next bust in style! 

 

Ghostbusters HasLab. Yes, we’re back. Again.  

 

 Ghostbusters TM & © 2024 Columbia Pictures Industries, Inc. All Rights Reserved. 

Cadillac and all related Emblems and vehicle body designs are General Motors Trademarks used under license to Hasbro, Inc.  HASBRO and all related logos and trademarks are trademarks of Hasbro, Inc. © 2024 Hasbro. 

Let's Build the Fanhome Ecto-1: Issue 30 (Stages 111 through 114)

Welcome to the next segment in our amazing Eaglemoss/Fanhome die-cast Ecto-1 build series. What began on the Ghostbusters Interdimensional Crossrip podcast continues here on the HQ website in a bit more detail. Want to build along with us? You can start from issue one (or if you started before Eaglemoss ghosted us all, you can also sign up to resume where you left off with Fanhome).

Last time on the show, we build Issue 29. You can check that out here. But this go-round, we’re diving into Issue 30, which really starts to put some of the finishing touches on the exterior of the Ecto and really bring it together.

Issue 30 has a few challenging steps, but still not the hardest among those (that distinction continues to belong to some of the initial engine building stages and for one particularly harrowing stage coming up in Issue 31. More on that in the next edition).

Stages 111, 112, and 113 will seem awfully familiar. Particularly if you’re saving up some shipments and building things in batches. These three stages are essentially the mirror of what was done in the previous issue for the Right Rear fin and reflector/lights. Refer back to our previous build blog for more on those and, well, just reverse it in your mind. A lot of the same challenges apply here to keep pieces in place while adhering them together with screws.

Once again, some painter’s tape really becomes your best friend, particularly as you’re trying to keep the wires in place behind the fins and the skirting (and to keep them attached to the small clips that are provided to wrangle a little). As more components of the car are permanently put into place, the wires do start to become a little less jumbled. But a little bit of easy to remove tape to the chassis of the car and/or a little wrap around some of the bundles will save you a world of headache.

Stage 114 is a great stage because it pretty much tops off the rear cargo area of the Ecto and, sans the roof rack gadgets and gak, gives you a pretty photogenic look at how the end product of your car is going to look!

Once again, wire wrangling ends up being one of the most difficult parts of this stage as you have to make sure that the wires for the lights are threaded into the small space just below the point where you’re about to place some chrome skirting. It takes a little bit of wiggling, but I was able to get the wires to stay in place as I snapped the skirting into place without tape this go-round.

It’s a bit unfortunate that I’ve gotten so used to flipping the car on its top to do work since, in the next issue, we’re about to start adding some of the roof rack lights and components. Which then means you need to very carefully place the car on its side when you’re doing work like this. Keen eyes will also note that I haven’t swapped out the passenger door for the fix that was received in the previous issue. At this point, reverse engineering to get the door off and back on might be a bit tricky and I’m still weighing just how much effort (and potential of breaking something) getting rid of that side-view mirror post is worth. Any thoughts? Let me know in the comments.

After you get the skirting on comes the fun part, attaching the rear license plate to the fender, then strapping that onto the back.

Once it’s on there, the rear end of the car is looking pretty close to done. You’ll see that some of the chrome trim that is applied with sticker glue is still peeling off. Basically all the points that I HAVEN’T dropped a little bit of Gorilla Glue onto are peeling up and sticking out. I’ve decided to wait until I’ve married the body of the car to the chassis before I start putting those little dabs of super glue on the trim and making sure they stop peeling, but it really is a nuisance. For all of the attention to detail and engineering on this awesome model, having those pieces just be metallic stickers that don’t permanently stick is a weird oversight. But easily remedied during a bit of clean up and polish when this is all said and done.

Lastly, in this issue, you receive the last component of the indicator arm that is going to finally allow you to affix the steering wheel onto the driver’s side column from way, way back in the day. Thank goodness I have one giant gallon-sized Ziplock that I kept all the small pieces that Eaglemoss wanted you to set aside for later (and that I didn’t lose said bag). Here’s the rub - the new indicator arm that is received, is pretty much identical to the one received previously with one exception, that it has a rubber spacer instead of being one full piece.

Don’t do as I did and put both of the indicator arms down and forget which is which because I had to cheat and go check out the amazing build happening at MyEcto1.com to remind myself which one was the new one and which one was the old one.

Once you swap out the indicator arm, it’s fairly easy to slot it onto the steering column and lock the wheel in place with a single screw. Then the end cap just snaps on there to cover up your work (another place that I feel might need just a little dab of Gorilla Glue to keep that from popping off at some point in the distant future).

After that, you’re all done and ready for the next issue!

Our thanks to the good folks at Fanhome for reviving the subscription build, sending us stages for review and for keeping the engine running for us all. If you’d like to start up your subscription, now is the time as they’re only offering new and continued subscriptions for a limited time… presumably because they’re dealing with the limited stock from the Eaglemoss days. So act now if you’re interested and happy building!

Let's Build the Fanhome Ecto-1: Issue 29 (Stages 107 through 110)

The build is back!

When Eaglemoss went under just about a year ago in July, I feared the worst for my subscription Ecto-1 build. The kit was a whole lot of fun. And, if you followed along with our builds on the Ghostbusters Interdimensional Crossrip podcast, Chris and I had a great chat every time we would sit and work on our models. It was a double-whammy to have lost the flow of subscription kits and to lose that amazing time with Chris. It sure seemed like a lot of us were going to be stuck with half (or less) built Ecto-1 models.

Enter the good folks at Fanhome, who have taken over the licenses from Eaglemoss and resurrected the subscriptions from the dead. You can now sign up to start from issue one, or pick up from where you may have left off with Eaglemoss and continue via Fanhome. Fanhome has made it super easy to pick which issue you need to begin with and their intuitive website and responsive customer service have been a breath of fresh air.

With the podcast having switched to a more infrequent model, I’ve decided to detail my builds here on the news blog hopefully as reference for those who may need it or for a quick overview for those of you who may be on the fence about joining the club. The model is amazing in quality, and Fanhome gives you all the tools that you need (with a few expendable exceptions like painters tape that I’ll get into a bit later here). If you’re a lot like me and you need 20-30 minutes of downtime to just follow instructions and enter a zen meditative state, this build is for you. It’s just challenging enough to make it fun without being frustrating and, as the end results start to come together, having your own faithful 1:8 scale Ecto sitting on shelf sure is cool as hell.

Fanhome was kind enough to send over a new initial kit, which we’ll be building here on the HQ in the future, but for now - I’m going to pick up with where I left off a year ago, with Issue 29 (Stages 107 through 110), which comprises parts of the left and right rear wheel wells, and the ‘59 Miller Meteor Ecto-1’s iconic red tail fins.

WIth that, let’s crack into it, eh?

When Issue 29 arrived, I cackled with glee. Again, not thinking that this model would ever see completion, getting a box in the mail from Fanhome was a treat. Fanhome sends your monthly subscription in a brilliant purple package, another step beyond the generic mailers that would come from Eaglemoss. The company is really making your monthly shipments a grand event, and it’s pretty cool.

The first thing you’ll notice with this issue’s shipment is that it includes a revised passenger front door. Eaglemoss had mistakenly sent out their kits with a passenger mirror recessed in the initial stage and had been promising a fixed door to those who waited. When it didn’t look like Eaglemoss was coming back, I went ahead and built out the door that I had been sent and attached it to the body of the car — so I’m not entirely sure what to do. Pulling the door off at this point would be a pretty dramatic overhaul. But if I’m going to do it, now’s going to be the chance. I set the revised door aside and… I’ll make that decision later. Worst case, I have an Ecto with a stem for a passenger mirror. Ha!

The door conundrum aside, Stage 107 is pretty straight-forward and a relative breeze. The right rear fender “crown” has just two steps. But key on this one is that the chrome trim at the top of the fin doesn’t attach permanently at this point in the build, so you have to be careful not to lose both it and the rear trim. If you plow through the whole issue, it isn’t that big of a deal. But if you pace yourself out and only do one stage at a time, don’t forget it’s another piece you need to set aside for later. Pro-tip: I have a gallon-sized Ziplock that I set aside which contains only the parts that you’ve set aside for later (things like the steering wheel, etc.). If I know I’m going to have to come back to it later, into the Ziploc it goes.

Stage 108, the Right Rear Reflector and Outer Light Lens is also pretty straightforward and cruises by in a snap. The one thing to look out for on this stage is that the outside inner lens is a very small clear piece that isn’t seated in the tray too well when you open it. Chances are, it will pop out when you open up the package and blends into its surroundings with relative ease. At first, I thought my kit was missing the lens but later discovered it floating in the tray.

Also a curious last step to this stage, you have to replace two screws on either side of the car’s body with flatter machine screws than what were initially installed. I’m thinking this was a course correct for an error that may have popped up earlier in the build. And, when you attach the whole completed part to the body of the car, it actually makes a lot of sense that you need a good flush connection to hold all the plastic pieces against the body of the car.

Stage 109 is where the challenge of this particular issue comes into play. The rear fins have two main pieces with two horizontally mirroring rear tail lights. And, while the assembly of the pieces in this stage isn’t the hardest of steps (that continues to be building the engine at the beginning of the build), the wiring to get the LED wires and bulbs into the tail lights is a bit tricky. You have to pull one of the wires marked R off of your assembled body and wire it into this piece. It took me a bit of trial and error but I found that bending the wire behind the bulb lens slightly to fish the bulb into the housing was a good first step. Then, using the flat back of the supplied tweezers, you can almost shoehorn the bulb into place. The bulb doesn’t seem to go ALL the way into the lens, but it does pop in enough that it won’t shake around or fall out of place.

Once you finally get the two LED bulbs plugged into the lenses, it becomes a matter of snapping everything together into place and then attaching it to the wheel well. This is one of those fun partworks stages where you wish that you had three hands: one to hold all the pieces together, another to push further down the part, and a third hand to be turning the screws to affix everything together. In some instances, a little painter’s tape helps. Or a clamp. But with a couple goes, I was able to snap this all together without additional assistance. Only minor hand cramping. I’m old. It happens. Ha!

With the whole piece assembled, here’s the fun part: attaching it to the main body of the car. Again, after staring at my poor Ecto-1 sitting on the shelf missing wheel wells and these red fins, boy-oh-boy was this gratifying to finally do. It felt like, after a long winter working on a 10,000 piece puzzle, finding the ONE piece that had been missing for months and dropping it into place. There’s quite a bit of hardware that goes into keeping this piece in place, and you have to be careful to thread the wires exactly as they’re shown in the diagram - because they need to snake all the way around the rear of the car and through the left side wheel well also. This is where I definitely recommend a little bit of painters tape to help act as that third hand for you to keep things in place, both during this stage and after. I dropped a little piece of painter’s tape under the cargo door to keep the two wires in place for the next couple stages. Also be sure that you’re using the red tab to keep the wires under the cargo door. Tuck those guys under before you affix the IM screw down.

After quite a bit of screw turning (there’s at least seven IM screws and four NP screws to this stage), I had to flip the body over to take a look and admire. It’s been a long time coming darlin’. You deserve this moment.

The final stage to this issue is a cakewalk. You’re basically prepping to work on the other side of the rear of the car by attaching the skirting to the left rear fending. It’s a quick and easy step that you can set the finished product aside and enjoy the rest of the awesome magazine contents and drop the booklet into your binder. Hopefully after all this time, you still have your binder and the prongs to attach the magazines to them.

All in all, this was a whole lot of fun. After a year and counting of not sitting down to work on the car, I had to shake out a little rust - and realized how over-caffeinated I was with my shaky hands. I’m just so glad to be getting monthly shipments again to finish off this car and finally have what will become one of the crown-jewels in the GBHQ collection.

Our thanks to the good folks at Fanhome for reviving the subscription build, sending us stages for review and for keeping the engine running for us all. If you’d like to start up your subscription, now is the time as they’re only offering new and continued subscriptions for a limited time… presumably because they’re dealing with the limited stock from the Eaglemoss days. So act now if you’re interested and happy building!

Hasbro Continues Their Retro Kenner Real Ghostbusters Line

F1180_F2702_F2703_PROD_GHB_Kenner_BANNER_5370x4200.jpg

Walmart.com as part of their new Virtual Con 2021 revealed that they will have three new Real Ghostbusters retro exclusives from Hasbro available on March 15th at 1pm Eastern. Among them are the iconic Fearsome Flush, Bug-Eye Ghost, and the biggest offering is a reissue of the Ecto-1!

For more, watch or listen to this Monday’s episode of the Ghostbusters Interdimensional Crossrip podcast, but in the meantime, here’s more information from Hasbro:

GHOSTBUSTERS KENNER CLASSICS ECTO-1

(Ages 4 and Up / Approx. Retail Price: $49.99/ Available: April 2021)

It's a (proton) blast from the past with the GHOSTBUSTERS Kenner Classics Ecto-1 from Hasbro! Inspired by The Real Ghostbusters cartoon, with design and deco influenced by the toys from the 80s, the Kenner Classics Ecto-1 toy features moving wheels, an opening tailgate, a roof-mounted swivel blaster seat, and a deployable ghost claw so kids can imagine bustin’ and capturing ghosts with the included ghost figure.

The Kenner Classics Ecto-1 is perfect for those wanting to relive the glory days of Saturday morning cartoons and ghostly green juice boxes or those who want to introduce a new generation of fans to the Ghostbusters. Available exclusively at Walmart.

GHOSTBUSTERS KENNER CLASSICS THE REAL GHOSTBUSTERS GHOSTS

(Ages 4 and Up / Approx. Retail Price: $14.99/ Available: April 2021)

It's a (proton) blast from the past with The Real Ghostbusters ghosts from Hasbro’s GHOSTBUSTERS Kenner Classics line! Inspired by The Real Ghostbusters cartoon, the packaging features design and deco influenced by the toys from the 80s. Kids can imagine eerie encounters with The Real Ghostbusters ghosts toys as it showcases fun action features, including cyclops eye-popping action from Bug-Eye and rolling action to reveal a fearsome ghost inside from Fearsome Flush.

The Real Ghostbusters Bug-Eye and Fearsome Flush toys from Hasbro’s GHOSTBUSTERS Kenner Classics line are perfect for those wanting to relive the glory days of Saturday morning cartoons and ghostly green juice boxes or those who want to introduce a new generation of fans to the Ghostbusters. Available exclusively at Walmart.

The Most Detailed LEGO Ecto-1 Ever is Coming November 15th!

LEGO and Ghostbusters.com announced an all-new, highly-detailed Ecto-1 kit inspired by Ghostbusters Afterlife today! Here’s all the news that’s fit to print along with the full press release via LEGO.

The latest LEGO set features:

  • All of the roof gear from the original film, including a moving ghost sniffer and radome. Both movements are activated by driving the car’s rear wheels

  • A trap door in the rear that can be activated by a lever on the roof to release a remote-controlled ghost trap

  • Rear passenger door opens to reveal a scissor-seat mechanism that extends and rotates the rear passenger seat out of the car using a trigger on the roof of the car

  • A 5-module steering wheel, corner brick with box, curved windscreen and pop out seat like in the movie

LEGO has announced an all-new Ecto-1 Creator kit coming November 15th, based on the upcoming film Ghostbusters Afterlife! Here's photos, discussion, and a lo...

The new LEGO Ghostbusters ECTO-1 is the most detailed LEGO brick recreation of the car ever produced and is the latest in a collection of film-based LEGO model building kits for adults who love building to relax and escape from the stresses of life. This set features two brand new LEGO brick elements including a new 6x14 curved windscreen and a new 5 module steering wheel.

Talking about the creation of the LEGO Ghostbusters Ecto-1, the set’s LEGO designer, Michael Psiaki said “I love creating LEGO vehicles, and having previously designed the LEGO James Bond Aston Martin DB5, I loved the challenge of working on the ECTO-1. This is the largest and most detailed version of this car that we have ever created. It is crammed full of authentic features and easter eggs that I’m excited for builders to discover as they put this model together.”

The LEGO Ghostbusters ECTO-1 contains 2,352 pieces and measures over 8” (22.5cm) high, 18” (47cm) long and 6” (16.5cm) wide. The set will be available from 15th November ahead of the release of the latest film in the Ghostbusters Franchise, Ghostbusters: Afterlife that launches in 2021.

LEGO Ghostbusters ECTO-1™ will be available directly via LEGO.com and LEGO Stores from November 15th.

For more information and to order yours, check out the official LEGO website!

, ,

In Stores and Online Now: Ghostbusters Ectomobile Owner's Workshop Manual

, ,

Now available wherever fine books are sold, the Ghostbusters: Ectomobile - Owner's Workshop Manual! This book goes far beyond just telling you tire pressure and oil change schedule. Learn how to properly operate a standard-issue Ghost Trap. Be kind to your fellow co-workers and finish the Containment Unit procedures to the final step. Learn how and why a Proton Pack uses ions to exhausted and ensnare the supernatural. All that plus do's and don'ts for uniforms and a whole lot more! No Ghostbuster should ever leave home without this handy reference guide - available for purchase on Amazon, at your local Barnes & Noble, the famous Ray's Occult in Manhattan, or wherever fine purveyors of supernatural manuscripts are sold!

FOLLOW GHOSTBUSTERS HQ ON THE SOCIAL NETWORKS